Tutorial: Photoshop for 70 basketball portraits in in two days | Dustin Snipes

In-depth Postproduction Tutorial by by Dustin Snipes

Tutorial: Photoshop for 70 basketball portraits in in two days

| by Dustin Snipes | photoshop, tutorial | photoshop, tutorial

For the last few months, people have been asking me about the post-production involved in the photos on my blog post “70 basketball portraits I did in two days.”

I always planned on sharing it with everyone but just haven’t had time to put anything together until now. Recently, I was asked to do a guest post for Scott Kelby’s blog and thought, “What better way to share this Photoshop tip with everyone than on Mr. Photoshop himself’s blog, Scott Kelby?” I was pretty giddy, to say the least.

It’s actually a pretty simple process that has a few steps to get this “look” (and its not LucasArts or HDR:)).

I wanted to make sure everyone who reads my blog also got to check it out as well.

Here goes:

There is one thing you must promise me–and yourself–before reading this post. Repeat (or read) after me:

“I, (state your name, or clever web user ID) will not overuse this technique on EVERY photo I take. I will only use it in moderation.”

Good, now that we got that out of the way, I just want to say that I don’t have an action made, nor do I think you should make one with this style of post processing. It all has to be about feel and knowing when you have gone too far or when to go further. It all varies depending on the scene and lighting. On this session of portraits, I went further than I normally would because that is what the client needed.

Step one: Lighting

To get a hard look, you have to have a hard light. I started with a three-light setup for most shots: Two back lights set at full power (Alien Bees Ab800) behind the subject, hitting the sides of their faces, and one in the front at a lower power with a small softbox. I added a fill light and background light when needed. See setups here.

This light set up changed slightly depending on the subject.

Step two: RAW Conversion

On this photo I started with a raw conversion and just slightly tweak levels to get the photo at a good color and contrast. The photo below is very close to raw, I cleaned a few dust spots that were on the photos from not cleaning my camera before…oops.

Step three: Dodge and Burn

The next step is a the one that really gives it that 3-D look. It’s were you take the subject’s highlights, shadows and features and “Carve” them out using dodging and burning.

Now there are a ton of ways to do this but this is how I do it. I first create a new layer by pressing (apple shift N) or by going to Layer/New on the top bar. I then change the blending mode to Softlight. Then change your brushes opacity to 5% and make sure it’s on 0% hardness. You can make two layers, one for highlights, one for shadows, but I usually just use one.

Next I go along and “paint” (with the brush) or enhance shadows and highlights that are already there. This really makes the photo pop out.

After this is done.

Step four: High Pass

I enhanced the contrast by duplicating the original image layer and de-saturating it by pressing (command (apple)-shift-”U”). This is important. If you don’t do this, your photo’s color will be really off once you select your blending mode. Then I select either soft light or hard light, depending on the amount of contrast I want to add.

The next thing I do is go to filter/other/high pass. This is what gives it the shinier look. This is also a key step because you must use judgement to determine how much of the effect you want. I usually go from somewhere between 100-200 depending on the amount of highlights I want to bring out. Again, you have to use your best judgement on this.

If the effect is still to much be sure to use your layers window and decrease the opacity on the high pass layer.

Step five: Color

The next thing I did was desaturate the reds in the photo. I used the hue/saturation window for this and changed the edit color from “master” to “red.”

Again, use your best judgment on this as well and take down as much or little as needed.

After I de-saturated the reds, I cropped and turned the image.

Step six: Final Touches

I’m almost done and I have the look I want, so I increase the contrast and brighten the photo.

Below is my final layers window.

As you can see, a lot of it is manual Photoshop, where you should tweak certain aspects and not rely on an action.

I hope that helps some of you in your Photoshop quests.

I would love to see finished products, so be sure to leave your comments here or on my blog with links to your finished work. If you have any questions, feel free to ask.

If you would like to see more photos and set up shots from the shoot click on the photo below.

via Tutorial: Photoshop for 70 basketball portraits in in two days | Dustin Snipes.

One response to “Tutorial: Photoshop for 70 basketball portraits in in two days | Dustin Snipes

  1. Pingback: Vintage Effect in 3 Easy Steps | MUST SEE'Z HERE·

Leave a Reply

Fill in your details below or click an icon to log in:

WordPress.com Logo

You are commenting using your WordPress.com account. Log Out / Change )

Twitter picture

You are commenting using your Twitter account. Log Out / Change )

Facebook photo

You are commenting using your Facebook account. Log Out / Change )

Google+ photo

You are commenting using your Google+ account. Log Out / Change )

Connecting to %s